Busbar insulation tubes, Heat Shrinkable ProductsCable End Sealing Caps, Cable End Caps Busbar Tubes, Cable Breakouts, heat shrink molded shapes, dip molded components Power cable accessories, Switchgear insulation products, Heat Shrink Tubings

Components for Cable Joints & Terminations

Gala is one of the leaders in manufacturing & supplying Components for Power Cable Accessories. One can count on our Electrical Cable Accessories to last for decades and to increase the reliability and efficiency of your grid. They are suitable for low, medium and high voltages applications and can operate under severe environments.

Below are the products offered for Components for Cable Joints & Terminations Industry
Heat Shrink Low Voltage Cable Breakouts

Gala's Heat Shrink Low Voltage Cable Breakouts provides a strong and permanent environmental seal to the crutch of 2, 3, 4, 5, 6 and 7 core PVC, XLPE Rubber and PILC cables upto 3.3 KV rated voltage.

Heat Shrink Non Tracking Cable Breakouts

Gala's Heat Shrink Non Tracking Cable Breakout provides permanent evironmental seal to the crutch of 3 core PVR PILC cable rate upto 36KV.

Heat Shrink Creepage Extension Skirt (Rain Shed)

Gala's Heat Shrink Rain Sheds are used to increase the surface creepage distance of the cores of cable termination without incressing the tail length. They are also used to avoid continuity during rainy season to avoid short circuiting of the elecrical network.

Heat Shrink Semi Conductivecable Breakout

Gala's Heat Shrink Semi Conductive Cable Breakout are used for PILC belted cable to seal the crutch area as well as to provide individual screening to each core.

Heat Shrink Right Angle / Straight Boot

Gala's Angleboots are Heat Shrink Right Angle / Straight Boots provide insulation to the bushings in the cable termination box, where the clearance between phase to phase and phase to earth is less then the normal air clearance. These boots provide protection against flashover in the event of high humidity, rodent menace and surge impulse.

Heat Shrink Medium/Heavy Wall Tubes

Gala's Medium wall and Heavy wall black tubing are used for environmental and mechanical protection of low voltage and medium voltage Cable Joints and insulating the connectors for low voltage straight through joints/splice rated up to 3.3KV. These tubes are manufactured from high-quality cross-inked polyolefin material.

Heat Shrink Wrap Around Sleeve

Gala's Wrap Around Sleeve is used to repair Cable Jackets.

Heat Shrink Red Insulation Tube

ala's Heat Shrink Red Insulation Tube is used to insulate the Joint area up to 66kV in Power Cable Joints for MV applications. This Tube is made from high-quality cross-linked material.

Heat Shrink Non Tracking Tube

Gala's Heat Shrink Non Tracking tubesbe are used in Medium Voltage Cable Terminations up to 66 KV. This Tube is made from high-quality cross-linked material that offers exceptional insulation and long-term service reliability.

Heat Shrink Stress Control Tube

Gala's Heat Shrink Stress Control Tube is used to control High Electrical Stress present at Insulation Screen Terminals and Power Cable Joints up to 66KV.

Heat Shrink Integrated Stress Control Tube

Heat Shrink GVOT Sleeve is manufactured from High Quality Cross-linked polyolefin material with integrated Stress Control system. It is used to protect cables or similar substrates in areas of extreme environmental conditions and high electrical stress.The tubing is normally used as an integral part of Gala Cable Terminations for voltages up to 24 kV.

Heat Shrink Double Layer Tube

Gala's Heat Shrink Double Layer is manufactured by Heat Shrinkable Insulating material and Heat Shrinkable Semi-Conductive material with special technology for good insulation in its inner layer and good semi-conduction in its outer layer; providing reliable shield protection.

Mastic Tape

Mastic Tape is a cold-applied butyl sealant designed for use in Cable Joint and Termination kits to offer excellent water sealing and weatherproofing.

Constant Force Spring

Gala's Contstant Force Sring is is used for solder free electric connection between metal cable elements & earthing device.

Clamps

Gala's Clampls are used to tighten onto the smallest diameter of a component within the working ranger for which it is designed.

Tinned Copper Braids

Gala's copper braid (Earthing braid) is used as an earth lead for Cable Joints and Terminations.