Cable Accessories - Heat Shrinkable Moulded Shapes 
Cable Accessories - ANGLEBOOT
Angleboots are Cable Accessories & Heat Shrink Right Angle / Straight Boots provide insulation to the bushings in the cable termination box, where the clearance between phase to phase and phase to earth is less then the normal air clearance. These boots provide protection against flashover in the event of high humidity, rodent menace and surge impulse.
The boots are mode from high quality cross linked non tracking polyolefin material. They are internally coated with water resistant red mastic.
RIGHT ANGLE BOOT
SELECTION CHART - RIGHT ANGLE BOOT
All dimensions are in mm
- Code
- D
- d
- P
- R
- T
- S
- F
- S
- F
- S
- F
- F
- (min)
- (max)
- (min)
- (Max)
- (min)
- (min)
- +/-10%
- GRB - 1
- 78
- 35
- 34
- 16
- 160
- 130
- 4.0
- GRB - 2
- 78
- 37
- 52
- 27
- 170
- 140
- 4.5
- GRB - 2A
- 90
- 37
- 67
- 27
- 170
- 140
- 4.5
- GRB - 3
- 145
- 72
- 67
- 34
- 170
- 150
- 4.5
STRAIGHT BOOT
SELECTION CHART - STRAIGHT BOOT
All dimensions are in mm
- Code
- D
- d
- A
- L
- B
- T
- S
- F
- S
- F
- F
- F
- F
- F
- (min)
- (max)
- (min)
- (Max)
- (min)
- (min)
- (min)
- +/-10%
- GSB - 1
- 80
- 34
- 34
- 21
- 140
- 225
- 30
- 3.6
- GSB - 2
- 80
- 35
- 58
- 22
- 140
- 225
- 30
- 3.6
- GSB - 2A
- 100
- 36
- 57
- 22
- 140
- 225
- 30
- 3.6
- GSB - 3
- 140
- 65
- 90
- 33
- 155
- 250
- 40
- 4.0
D,d : Internal Diameter ; s : as supplied ; f : after free recovery ; Tb,Tc : Thickness of body & core
TECHNICAL SPECIFICATION
- PROPERTIES
- VALUE
- STANDARD
- Physical
- Tensile Strength
- 12 N/mm2 (MPA)(min.)
- ASTM D638
- Ultimate Elongation
- 350% (Min.)
- ASTM D638
- Density
- 1.15 + 0.2 gm/cm3
- ASTM D792
- Hardness
- 45 + 10 Shore D
- ASTM D2240
- Water Absorption
- 0.5 % (max.)
- ASTM D570
- Thermal
- Accelerated Ageing
- (120oC for 500 Hrs)
- ASTM D2671
- Tensile Strength
- 11 N/mm2 (Mpa) (min.)
- ASTM D 638
- Ultimate Elongation
- 300%(Min.)
- ASTM D638
- Low temperature Flexibility (-40oC for 4 Hrs.)
- No Cracking
- ASTM D2671
- Heat Shock (250oC for 30 Min.)
- No Cracking or flowing
- ESI 09-11
- Shrink Temperature
- 125oC
- IEC 216
- Continuous Temperature limit
- -40oC to + 110oC
- IEC 216
- Electrical
- Dielectric Strength
- 15 KV/mm. (Min.)
- ASTM D149
- Volume Resistivity
- 1 x 1014 Ohm.cm(min.)
- ASTM D257
- Dielectric Constant
- 5 (Max.)
- ASTM D150
- Resistant to track & erosion
- No tracking, erosion or flame failure upto 3.25 KV for 20 min.
- ASTM D2303
Products
Heat Shrinkable Moulded Shapes
Heat Shrink Tubes / Heat Shrink Sleeves
- Advantages Of Heat shrink Tubing
- Thin Wall Tubes
- GDW : Dual Wall Tubing
- Medium/Heavy Wall Tubes-Commercial
- Heat Shrink Co-extruded Tubing Premium Quality
- Red Insulation Tubes
- Non Tracking Tubes
- Busbar Sleeves
- Stress Control Tube
- Integrated Stress Control Tube-GVOT Tube
- Heat Shrink Double Layer Tube-GDTL Tube
- High Shrink Ratio Heat Shrink Tube
Switchgear Insulation Products
- Barrier Board Sheet
- End Sealing Kit for Extensible RMU/GIS Bushing
- Heat Shrink Bus Bar Sleeve
- Bus Bar Insulating Shrouds
- Bus Bar Insulating Shrouds Polyolefin
- Bus Bar End Caps
- Thin wall tube wire marking
- Heat Shrink Tape (Bustape)
- Insulation for Circuit Breakers
- Busbar Sleeve for 66 kV
- Bushing Boot
- Non Shrinkable High Voltage Tape
- Heat Shrinkable Gland
